Tenber Knowledge Center

Conductivity Controller for Cooling Tower Blowdown: Selection and Control Checklist

A conductivity controller for cooling tower blowdown should measure a representative water stream and convert the result into an agreed bleed or alarm action. Select the sensor, cell constant, temperature compensation, relay logic, 4–20 mA or Modbus connection together. Set the alarm from the site’s water chemistry and operating baseline, not a universal conductivity number.

What does conductivity control do in a cooling tower?

Cooling-tower evaporation removes water but leaves many dissolved substances in the circulating water. As concentration changes, conductivity can be used as an operating indicator for a bleed or blowdown decision. The controller does not determine the complete water-treatment recipe by itself. The site still needs operating limits, chemical-treatment rules, make-up-water information and a safe control response.

The measurement point must represent the circulating water that the project intends to control. A sample taken immediately after chemical injection, in a stagnant pocket or where air bubbles enter can create a value that does not represent the tower loop. Installation, flow, temperature, sensor fouling and calibration should be treated as part of the control system.

For a general conductivity measurement explanation, see Tenber’s conductivity sensor cell-constant selection guide. This article narrows the topic to cooling-tower blowdown selection, measurement points and control integration.

Where should a cooling-tower conductivity sensor be installed?

Choose the point from the control objective rather than from the easiest pipe to access. A suitable point should be representative, maintainable and compatible with the sensor assembly.

Measurement pointPotential useMain questions to answer
Recirculating water lineControl the circulating-water concentration trendIs the flow stable? Is the water mixed? Can the sensor be isolated and cleaned?
Side-stream or bypass loopMake the sensor easier to service and calibrateWhat flow, pressure and temperature does the bypass maintain? Is the sample representative?
Blowdown lineObserve water being dischargedDoes the line provide stable flow during the control decision? Will the reading lag the tower condition?
Make-up lineCheck incoming-water qualityIs this a monitoring point only, rather than the main blowdown control point?

The final point depends on the tower design, water-treatment procedure and control narrative. A supplier should not choose the sensor location from the words “cooling tower” alone.

Which specifications matter in a conductivity blowdown controller?

Conductivity range and cell constant

The expected conductivity range affects the sensor and cell constant. A low-conductivity make-up-water measurement and a concentrated circulating-water measurement may require different sensor arrangements. Confirm normal, minimum, maximum and upset values rather than selecting a cell constant from a generic catalogue line.

The conductivity sensor should be reviewed with the controller, temperature element, cable and mounting. The controller may support multiple measurement modes, but that does not mean every sensor or range is suitable for every cooling-water condition.

Temperature compensation

Cooling-tower water temperature changes during operation. Confirm automatic or manual temperature compensation, the temperature sensor type, expected temperature range and reference temperature used by the control procedure. A conductivity value without a clear temperature basis can be difficult to compare over time.

Blowdown relay logic

A relay may start a valve, signal a PLC, trigger an alarm or provide an interlock, depending on the model and plant design. Confirm relay quantity, contact rating, high/low setpoint, hysteresis, delay and the required fail-safe state. Do not connect a blowdown actuator simply because a controller has a relay; the final electrical load and safety logic require engineering review.

4–20 mA and RS485 integration

Use isolated 4–20 mA when the PLC needs a hardwired conductivity value or when the existing panel standard is analogue. Use RS485 Modbus RTU when the PLC or gateway can read digital registers and the project needs additional values or diagnostic information. Confirm scaling, register mapping and communication-loss handling before commissioning.

Which Tenber conductivity controller should be reviewed?

The following comparison identifies possible starting points from the current documentation. It is not a guarantee that a model is suitable for every cooling-tower water condition.

ModelDocumented functions relevant to selectionWhen it may fitWhat to verify before quotation
EC-703Conductivity/TDS/resistivity measurement, one isolated 4–20 mA output and two relay outputs are documented on current product materialA compact blowdown or alarm loop needing analogue output and relay functionsConductivity range, sensor/cell constant, temperature input, relay settings, output scaling and exact variant
EC-702Conductivity-related measurement, isolated 4–20 mA output, RS485 Modbus RTU and relay settings are documented in current manual notesA PLC/DCS project needing analogue output, Modbus supervision or model-supported relay logicExact current variant, register map, temperature sensor, output range, relay rating and installation limits
ECS-7301Conductivity, resistivity, salinity and TDS measurement, two isolated current outputs and RS485 Modbus RTU are documentedA monitoring and integration project needing more than one process value or digital communicationCooling-water range, sensor type, cell constant, output assignment, Modbus registers and whether local relay control is required

The Tenber EC-703 conductivity controller is a logical product page to review when the project needs a compact conductivity/TDS/resistivity controller with documented analogue and relay functions. The EC-702 conductivity controller should be reviewed when the integration brief includes RS485 Modbus RTU. The ECS-7301 conductivity meter may fit broader conductivity-related monitoring requirements.

How should the blowdown setpoint be chosen?

There is no universal cooling-tower conductivity setpoint that can be safely copied into every plant. The target depends on make-up-water chemistry, cycles of concentration, corrosion and scale-control practice, treatment chemicals, tower materials, discharge requirements and the site operating procedure.

  1. Record make-up-water conductivity and temperature.
  2. Record circulating-water conductivity at stable operating conditions.
  3. Confirm the unit, temperature basis and sensor calibration procedure.
  4. Define the normal operating band with the water-treatment engineer.
  5. Set high and low alarm values with enough hysteresis to prevent relay chatter.
  6. Define what happens when the reading is high, low, unstable or unavailable.
  7. Test manual blowdown, automatic blowdown, valve feedback and PLC interlocks separately.
  8. Review the trend after commissioning and adjust only through the approved operating procedure.

Conductivity is an indicator, not a complete diagnosis. A high reading may reflect concentration, make-up-water change, chemical addition, sensor fouling, temperature-compensation error, poor flow or an installation problem. The alarm should initiate a documented check instead of automatically claiming membrane, scale or corrosion failure.

What is suitable and not suitable for cooling-tower blowdown control?

Suitable applications

  • Industrial cooling-water loops with a representative and maintainable measurement point.
  • Towers where the water-treatment team has defined a conductivity operating band and response plan.
  • PLC/DCS or local-panel projects with a specified 4–20 mA, RS485 Modbus RTU or relay requirement.
  • OEM or engineering projects that can provide sensor material, cell constant, temperature and mounting requirements.
  • Replacement projects where the existing control panel, signal range and actuator load are documented.

Not suitable without further review

  • Selecting a controller only from the phrase “cooling tower conductivity” without a range or water-chemistry record.
  • Using a make-up-water reading as the blowdown-control value without checking process representativeness.
  • Installing the sensor in a stagnant line, directly after chemical injection or where air bubbles make the reading unstable.
  • Treating TDS as a universal substitute for conductivity without confirming the configured conversion factor and process chemistry.
  • Connecting a relay directly to a valve, pump or dosing device without checking contact rating, interlocks and fail-safe behaviour.
  • Applications requiring hazardous-area, sanitary, pressure or temperature approvals that have not been confirmed.

What should you confirm before requesting a quotation?

RequirementExample information to send
Water source and processMake-up water, circulating water, side-stream or blowdown line
Conductivity rangeNormal, minimum, maximum and alarm values with units
TemperatureNormal and maximum temperature; temperature sensor type if known
Sensor and cell constantExisting sensor model, electrode material, cell constant or requested mounting
InstallationPipe, tank, bypass, flow cell, pressure, flow and isolation method
Output4–20 mA, RS485 Modbus RTU, relay or mixed interface
Control actionAlarm, bleed valve, blowdown pump, interlock or PLC command
Electrical detailsSupply, cable length, PLC input, load and panel standard
Quantity and destinationNumber of points, replacement or new project, destination country

For a model review, sensor match and quotation, use Tenber’s conductivity controller inquiry page. Send the existing controller or PLC I/O list when replacing an installed instrument.

Sources, author and update record

This guide was prepared by the Tenber Technical Team and updated September 21, 2026. Technical references include current Tenber EC-702, EC-703 and ECS-7301 product documentation and the linked product pages. Cooling-tower chemistry, setpoints, discharge requirements and control safety remain site-specific and must be confirmed by the project owner or water-treatment engineer.

Request a Quote