Tenber Knowledge Center

Conductivity vs Resistivity in Water: Which Should You Monitor?

Quick answer: Conductivity and resistivity describe opposite sides of the same electrical property: higher conductivity means lower resistivity. For most process-water loops, conductivity is a practical trend signal; resistivity is useful when a high-purity stream has very low conductivity. Choose the measurement, units, temperature basis, sensor range and alarm limits from the project specification. Neither value identifies individual contaminants.

What is the difference between conductivity and resistivity?

Conductivity measures how readily water carries electrical current. Dissolved substances can form electrically charged ions that carry current. Resistivity describes the opposing property: electrical resistance. For the same sample, geometry and temperature reference, conductivity and resistivity are reciprocal.

Water conductivity is commonly reported in microsiemens per centimeter (µS/cm) or millisiemens per centimeter (mS/cm); some standards use siemens per meter (S/m). Resistivity is often reported in megohm-centimeters (MΩ·cm). Confirm units before comparing instruments or setting alarms. A change in conductivity may indicate a change in ionic loading, leakage or concentration, but it does not identify the cause.

How do you convert conductivity and resistivity?

When both readings use the same temperature reference, resistivity in MΩ·cm equals 1 divided by conductivity in µS/cm. For example, 1 µS/cm corresponds to 1 MΩ·cm, while 0.1 µS/cm corresponds to 10 MΩ·cm. This relationship is a unit conversion, not a water-quality limit. Do not compare a temperature-compensated value with an uncompensated value without checking the basis.

When should a plant monitor conductivity of water?

Conductivity is commonly used to track changes in feedwater, cooling water, wastewater, boiler-water loops and reverse-osmosis systems. It can support process monitoring when the sample point, sensor and range are appropriate. The project specification should define the acceptance limit and what action follows an alarm.

For reverse osmosis, treat feed and permeate as separate sample points. Define a range and limit for each; do not apply one generic threshold to every plant. Record the water source, expected range, normal and upset temperature, installation point and required PLC or recorder signal. A conductivity reading is a water quality indicator, not a complete chemical analysis.

When is resistivity more useful?

Resistivity can express very low conductivity clearly in high-purity water applications. Confirm that the project specification asks for resistivity and that the controller supports the required display or output. High-purity samples can be sensitive to temperature and handling, so follow the applicable method and current instrument manual. ASTM D5391 addresses flowing high-purity water samples; verify its scope and edition for the project.

Do not assume every RO permeate system needs a resistivity display. Many RO projects specify conductivity. A grab sample exposed to air may not represent the online stream, so use the sampling method required by the process.

How does a conductivity sensor cell constant affect the reading?

A conductivity cell has a geometry represented by its cell constant. The instrument uses that constant to relate measured conductance to the reported conductivity. The cell constant must suit the expected range and installation. A sensor intended for a different range may not provide the resolution or operating span needed for the process.

Check the manufacturer’s stated cell constant, measurement range, wetted materials, process fitting and temperature input. A representative sample and suitable flow also matter. Record the units and temperature reference with each reading so operators can compare like with like.

What is suitable, and what is not suitable?

  • Ordinary process-water loop: conductivity may be a useful starting measurement when range, cell constant and installation fit. Confirm the alarm limit from the process specification.
  • High-purity loop: consider resistivity if the specification requires it. Confirm temperature handling and sample method; do not infer purity from one reading alone.
  • RO feed and permeate: monitor them as distinct points with separate project limits. Do not reuse one setpoint automatically.
  • Contaminant identification or certification: conductivity and resistivity alone cannot identify every substance or certify water composition. Use relevant laboratory or process-specific analysis.

Which Tenber conductivity products should be reviewed?

Review the Tenber EC-702 conductivity controller and EC-703 conductivity controller against measurement range, sensor input, output, relay and communication requirements. Review the TB85EC1A/B conductivity sensor for its documented cell constant, materials and process connection. These are starting points, not a guarantee that a combination suits every installation. Check current manuals and exact variants before ordering.

For broader model options, see Tenber’s conductivity instruments. Confirm output mapping and PLC input with the current model documentation rather than assuming a feature from a family name.

What should you confirm before requesting a quotation?

Provide the application and water source, expected and upset conductivity range, units, temperature, pressure, sample location, fitting and cell constant if known. Add cable length, PLC or recorder input, alarm or control requirement, quantity and destination market. A photo of the installation and existing instrument labels can help identify mismatches. Request a model review or quotation with these details.

Frequently asked questions

Does conductivity equal TDS?

No. Some instruments estimate total dissolved solids (TDS) from conductivity using a selected conversion factor. That estimate is not a direct measurement of each dissolved substance.

Is higher resistivity always better?

It indicates lower ionic conductivity for the same temperature basis, but it does not identify non-ionic contaminants or prove that water meets every application requirement.

Sources, author and update record

Sources: USGS specific-conductance guidance; ASTM D5391; current Tenber EC-702, EC-703 and TB85EC1A/B product documentation. Author: Tenber Technical Team. Updated October 19, 2026. Confirm model limits in current manuals before specification.

Request a Quote