Quick answer: A conductivity controller for chemical dosing should be selected by matching the liquid, conductivity range, temperature compensation, dosing objective, output signal and relay logic. Set the control point from a verified process relationship, then define deadband, delay, alarm action and fail-safe behavior before requesting a quotation.
What does a conductivity controller do in a chemical dosing loop?
A conductivity controller measures the electrical conductivity of process water and uses the result for display, analogue transmission, alarm or local control. In a dosing loop, the controller can provide a process signal to a PLC or activate a relay when the measured value crosses a configured threshold.
Conductivity is often used as an indirect process indicator. It may relate to dissolved salts, chemical concentration, rinse quality, blowdown demand or the condition of a treatment step. The relationship is process-specific, so a conductivity value should not be treated as a universal concentration reading without a verified process curve.
The complete loop normally includes a conductivity sensor, a controller or transmitter, a dosing pump or valve, a chemical tank, a mixing zone and a control system. A correct controller cannot compensate for a poor sensor location, insufficient mixing or an unsuitable dosing response.
When is conductivity-based chemical dosing worth reviewing?
Review conductivity-based control when the process has a repeatable relationship between conductivity and the dosing decision. The method may be considered for chemical preparation, rinse-water control, salt or brine handling, process-water conditioning and other industrial applications where conductivity changes as the process changes.
Before selecting equipment, record what the measured value is expected to do. Is it used to start a dosing pump, stop a pump, open a valve, trigger an alarm, send a PLC value or confirm that a rinse step is complete? The answer affects the required outputs and the control architecture.
What should be defined before choosing the controller?
| Selection item | Why it matters | Information to prepare |
|---|---|---|
| Conductivity range | The controller and sensor must cover the normal operating window without losing useful resolution. | Minimum, normal and maximum conductivity, unit and expected process temperature. |
| Liquid and chemistry | Fouling, corrosive chemicals, suspended solids and concentration changes affect sensor selection and maintenance. | Liquid name, composition, solids, temperature, pressure and cleaning conditions. |
| Dosing objective | A monitoring loop, alarm loop and automatic dosing loop need different control decisions. | Target value, response direction, pump/valve action and operator override. |
| Signal integration | The receiving panel must accept the selected output and scaling. | 4–20 mA, RS485 Modbus RTU, relay contacts, PLC input type and register requirements. |
| Mixing and delay | The measured value may change only after the chemical has travelled and mixed. | Pipe length, tank volume, flow, mixing time and expected process response. |
How should a conductivity dosing setpoint be chosen?
Start with process data rather than a generic conductivity number. Measure the normal operating range under stable conditions and relate each measurement to the actual process decision. If the controller is intended to maintain a target concentration, verify the relationship between conductivity, chemical concentration and temperature.
Define at least three values:
- Target value: the preferred operating point or control band.
- Action value: the point at which dosing starts, stops or changes state.
- Alarm value: a limit that requires operator attention or a process response.
These values do not have to be identical. A small gap between the operating target and the action value can cause frequent switching. A large gap can create slow correction or excessive chemical addition. The final setting should be validated during commissioning with representative samples and the approved process method.
What is deadband and why does it matter?
Deadband, also called hysteresis, is the difference between the point where a control action starts and the point where it stops. It prevents a relay or dosing output from changing state every time the measured conductivity fluctuates around one threshold.
| Control design | Example behavior | Risk to review |
|---|---|---|
| Single threshold | Start or stop dosing at one value. | Rapid cycling when the reading moves slightly around the threshold. |
| Two-point deadband | Start dosing at a high or low action value and stop at a separate return value. | Deadband that is too narrow may still cycle; too wide may delay correction. |
| PLC control with process delay | Controller transmits the value and the PLC applies logic after a defined delay. | Incorrect delay can cause overshoot, repeated dosing or unstable control. |
| Alarm-only control | Controller reports a limit violation while an operator or PLC decides the action. | Alarm may be ignored if the responsible action is not documented. |
The deadband should reflect process variation, sensor repeatability, mixing time and the consequence of over-dosing. Do not copy a deadband from another plant without checking the actual liquid and control response.
How should relay logic be reviewed?
Define the normal state
Document whether the relay is normally energized or normally de-energized during healthy operation. A fail-safe design may use a relay state that changes when power or signal is lost, but the exact behavior must be confirmed in the current controller documentation and panel design.
Separate control from alarm
Do not use one relay for both dosing control and a critical fault alarm unless the project specification explicitly allows it. A dosing relay may operate frequently, while an alarm relay may need to remain active until an operator acknowledges the condition.
Add time delay where the process needs it
A time delay can prevent a short conductivity spike from starting a chemical pump. It can also allow the process to mix before the controller evaluates the result. Confirm whether the delay is configured in the controller, the PLC or the dosing pump, and document the responsible device.
Define sensor-fault behavior
Specify what happens when the sensor is disconnected, outside range, contaminated or not yet stable. Depending on the process, the safe response may be to stop automatic dosing, hold the last state, switch to manual operation or generate an alarm. This decision belongs in the control narrative, not only in the quotation notes.
4–20 mA or RS485 for conductivity dosing?
Use 4–20 mA when the PLC or dosing panel needs a straightforward analogue process value with defined scaling. Use RS485 Modbus RTU when the project needs digital communication, multiple values, diagnostic information or centralized parameter access. Some projects use both, with analogue output for a simple control path and RS485 for supervision, subject to the supplied variant.
| Requirement | Possible signal | Confirm before ordering |
|---|---|---|
| Simple conductivity value to PLC | Isolated 4–20 mA | Range, units, scaling, fault current and input isolation. |
| Digital supervision and parameters | RS485 Modbus RTU | Register map, address, baud rate, parity and data format. |
| Local pump or valve action | Relay output | Relay rating, control direction, deadband, delay and interlock. |
| More than one process value | Multiple outputs or digital communication | Conductivity, temperature, alarms and output assignment. |
For a broader signal comparison, review EC-702 vs EC-703 for RS485 and 4–20 mA conductivity control and the conductivity controller installation and wiring checklist.
Which Tenber conductivity controller should be reviewed?
The Tenber EC-703 conductivity controller is a logical product page to review when a project needs conductivity-related measurement, analogue integration and local relay functions. Confirm the current manual, sensor compatibility, conductivity range, temperature input, output assignment and exact supplied variant before quotation.
If the panel requires RS485 Modbus RTU or a different combination of analogue and relay functions, compare the current model documentation and the conductivity transmitter selection guide. Do not assume that two controllers with similar front-panel functions accept the same sensor or expose the same register map.
What is suitable and not suitable for conductivity dosing control?
Suitable applications to review
- A repeatable relationship exists between conductivity and the dosing decision.
- The sensor is installed after sufficient mixing and away from chemical injection turbulence.
- The project defines target, action, alarm, deadband, delay and manual override behavior.
- The PLC, dosing pump or valve has a documented response to signal loss and sensor faults.
- Operators can verify the online value with a representative sample or approved reference method.
Not suitable without further confirmation
- The liquid concentration changes independently of conductivity or the relationship has not been verified.
- The sensor point is before adequate mixing, inside a dead zone or exposed to air bubbles and chemical injection shock.
- The project requests automatic dosing without describing the safe state when the sensor fails.
- The expected range, temperature, cell constant or sensor type is unknown.
- The quotation asks for a controller model but omits the signal, relay and installation requirements.
What should you confirm before requesting a quotation?
Send the liquid name and composition, expected conductivity range, process temperature, pressure and flow, target concentration if applicable, dosing chemical, injection point, mixing distance, sensor mounting, cleaning method, power supply, required 4–20 mA channels, RS485 requirement, relay action, deadband, delay, alarm behavior, PLC model, quantity and destination country.
If the project also monitors pH, turbidity or dissolved oxygen, review the online water quality monitoring system components guide. For a configuration review, use the Tenber inquiry page and include the control objective rather than only the desired conductivity number.
Sources, author and update record
Author: Tenber Technical Team
Updated: October 4, 2026
Sources: Tenber EC-703 product documentation and the linked conductivity controller, transmitter, wiring and signal-selection guides. Confirm the current manual, sensor range, temperature limits, output assignment, relay rating and communication registers before purchase or commissioning.