Quick answer: An open-channel turbidity sensor is selected for gravity flow, channels, tanks or non-full pipes where a standard inline probe cannot maintain a stable measuring position. Choose the installation point by checking representative flow, immersion depth, bubbles, solids distribution, cleaning access and signal integration. Confirm the sensor and controller variant before quotation.
What is an open-channel turbidity sensor?
An open-channel turbidity sensor measures suspended-particle scattering in a channel, tank, wet well or other installation without relying on a full pressurized pipe. It can be useful when wastewater or process water moves by gravity or when the flow level changes during operation.
The sensor still needs a stable and representative measuring zone. A location that is too close to an inlet, drop, pump discharge, wall, bottom or air entrainment point may produce readings that do not represent the wider process. Installation is part of the measurement specification, not an afterthought.
When should an open-channel installation be considered?
Review an open-channel arrangement when the liquid flows through a flume, channel, tank, wet well, equalization basin or partially filled pipe. It may also fit a project where a bypass flow cell is impractical or where operators need access for inspection and cleaning.
First confirm the normal, minimum and maximum liquid level. The sensor must remain immersed at the measurement point, and the optical path or sensing area must not be blocked by the channel wall, bottom, floating material or accumulated sludge.
Open channel vs bypass vs direct pipe turbidity measurement
| Installation | When it may fit | Main point to verify |
|---|---|---|
| Open channel or tank | Gravity flow, changing level, wet well or non-full pipe | Immersion depth, representative flow, bubbles, solids distribution and cleaning access |
| Bypass or flow cell | Process line is pressurized or the main pipe is difficult to access | Flow velocity, isolation valves, sample representativeness, pressure and drain arrangement |
| Direct pipe | Full pipe and stable process conditions are available | Insertion position, bubbles, fouling, pipe diameter, pressure and sensor orientation |
Where should an open-channel turbidity sensor be installed?
Choose representative flow
Choose a point after the liquid is reasonably mixed but before solids settle or separate. Avoid a quiet corner where heavier particles collect and avoid a high-energy drop where bubbles dominate the optical signal. If the process has several streams, confirm whether the selected point measures the combined flow or only one branch.
Control the liquid level
Record the minimum operating level, normal level and maximum level. The sensor should stay submerged across the intended operating range. If the level changes widely, consider a stilling arrangement, controlled-depth mounting or a bypass sample point, subject to the current sensor documentation.
Keep the optical path clear
Do not place the sensing area against the channel bottom or wall. Leave enough clearance for the liquid to surround the sensor and for operators to remove it for cleaning. Confirm the mounting bracket, insertion length, cable protection and maintenance access before fabrication.
How do bubbles and solids affect turbidity readings?
Air bubbles can scatter light and create short spikes or unstable readings. Turbulence at an inlet, aeration point, weir or pump discharge can therefore make an otherwise correct sensor appear unreliable. Choose a location with stable flow while preserving a representative solids concentration.
Solids can also settle, float or form layers. A measurement near the bottom may read higher than the bulk liquid when sediment accumulates. A measurement near the surface may miss heavier solids. Review the process mixing pattern and compare the sensor location with manual samples during commissioning.
What mounting options should be reviewed?
| Mounting question | Why it matters | Information to provide |
|---|---|---|
| Fixed immersion | Simple access in a channel or tank, but level and clearance must remain stable | Level range, bracket position, immersion depth and removal method |
| Retractable or removable | Useful where cleaning and inspection are frequent | Isolation method, safe removal procedure and cable protection |
| Bypass or flow cell | Can provide controlled flow and easier isolation | Sample take-off, flow range, pressure, valves, drain and return point |
| Submersible installation | May suit wet wells or basins with changing geometry | Suspension, lifting, fouling, minimum level and maintenance access |
How should the signal connect to a PLC or monitoring system?
Define whether the turbidity value will be read locally, sent through 4–20 mA, transmitted over RS485 Modbus RTU, or used with a relay or alarm function. Confirm the engineering unit, scaling, update behavior, fault output and receiving-channel configuration.
Review the turbidity sensor signal-scaling guide when the panel team is assigning the PLC input. The signal choice does not correct a poor installation point, incorrect calibration or an unsuitable cleaning schedule.
Which turbidity product should be reviewed?
The Tenber TUR-6308 turbidity controller is a product page to review when a project needs an industrial turbidity measurement and control configuration. Confirm the current sensor compatibility, range, mounting arrangement, output assignment and controller variant before ordering.
| Project condition | Possible starting point | Confirm before quotation |
|---|---|---|
| Gravity wastewater channel | Open-channel or submersible measurement review | Minimum level, solids profile, bubbles, bracket and cleaning access |
| Pressurized process line | Direct pipe or bypass review | Pressure, pipe size, flow, valves, insertion point and isolation |
| PLC or SCADA integration | Controller plus defined analogue or digital signal | Scaling, protocol, register map, alarms and fault handling |
For broader sensor selection, compare the industrial turbidity sensor selection guide and the pipe, tank and bypass installation guide.
How should an open-channel turbidity sensor be commissioned?
- Verify that the sensor remains immersed at the minimum process level.
- Check that bubbles, floating material and settled solids are not concentrated around the sensing area.
- Confirm the controller range, units, output scaling and alarm behavior.
- Compare the online value with a representative manual sample using the approved method.
- Record the cleaning interval, calibration method, inspection point and responsible operator.
Commissioning should document the actual installation, not only the controller settings. If the online value changes after cleaning, rainfall, aeration or flow redistribution, investigate the process and measurement point before changing the alarm limit.
What is suitable and not suitable?
Suitable applications to review
- Gravity-flow wastewater channels, equalization tanks and wet wells with a defined minimum level.
- Industrial process-water tanks where operators can reach and clean the sensor.
- Projects with a known solids distribution and a documented online-to-manual comparison method.
- Monitoring systems that define the output, alarm response and maintenance responsibility.
Not suitable without further confirmation
- Channels with unknown or rapidly changing level where the sensor may be exposed.
- Locations immediately beside an inlet, aerator, drop, pump discharge or heavy sediment zone.
- Applications requiring a guaranteed turbidity result without a validated sampling and calibration method.
- Projects that request a sensor model without specifying liquid, range, mounting and signal requirements.
What should you send before requesting a quotation?
Send the liquid and process description, turbidity range and unit, normal/minimum/maximum level, channel or tank dimensions, flow direction and rate, solids type, temperature, pressure if applicable, bubbles or aeration, mounting preference, cable length, cleaning access, calibration method, 4–20 mA or RS485 requirement, alarm action, quantity and destination country.
If more than one parameter must be monitored, review the online water quality monitoring system components guide. Use the Tenber inquiry page to describe the installation point and request a sensor-controller configuration review.
Sources, author and update record
Author: Tenber Technical Team
Updated: October 3, 2026
Sources: Tenber TUR-6308 product documentation and the linked turbidity installation, selection and signal-integration guides. Confirm current manuals, sensor range, mounting limits, output assignment and maintenance instructions before purchase or commissioning.