Tenber Knowledge Center

Dissolved Oxygen Calibration Pressure Correction Guide

Dissolved Oxygen Calibration Pressure Correction Guide

A DO probe can pass calibration with the wrong pressure setting. If it disagrees with a handheld meter, check the pressure input on both devices first. The probe may not be the fault.

For dissolved oxygen calibration pressure correction, use the local, absolute air pressure as the instrument manual specifies. A weather app may show a value adjusted to sea level. Do not copy that value into a meter that needs local pressure.

How does barometric pressure affect dissolved oxygen calibration?

Barometric pressure affects the partial pressure of oxygen in air. That changes how much oxygen water can hold at air saturation. At the same temperature and salinity, a lower air pressure means a lower oxygen concentration in mg/L. The calibration reference must allow for this change.

Temperature, pressure and salinity all affect the result. A meter with a temperature sensor may still need you to enter the air pressure. The USGS DOTABLES tool uses these inputs to calculate oxygen solubility. Use it within its stated ranges.

Follow the manual for the exact controller and sensor pair. For wider planning and records, see our water quality sensor calibration guide.

Which pressure value should you enter into a DO meter?

Read the pressure field description before entering a number. Local pressure, sea-level pressure and process pressure describe different conditions.

Pressure termWhat it describesCalibration decision
Local or station pressureActual atmospheric pressure at the siteUse when the manual asks for true barometric pressure
Sea-level corrected pressureWeather value adjusted for elevationDo not copy into a local-pressure field
AltitudeSite elevation above sea levelEnter only if the instrument uses an altitude setting
Pipe or tank gauge pressurePressure relative to the surrounding atmosphereNot the local atmospheric calibration value
Standard atmosphereA fixed reference: 101.325 kPaNot a measurement of today's site pressure

Record the pressure source, time, place and unit. A number alone is hard to check later.

If you use weather data, ask whether it shows station pressure or a sea-level value. If you need to convert it, follow the instrument maker's method. Wisconsin DNR's calibration guidance explains the difference.

Check hPa, mbar, kPa and mmHg

One kPa equals 10 hPa, and one hPa equals one mbar. Standard atmospheric pressure is 101.325 kPa, 1013.25 hPa or 760 mmHg. These are equivalent reference values, not universal calibration settings.

For example, 98.6 kPa equals 986 hPa. If the field asks for hPa, do not enter 98.6. The value would be ten times too small. This is a unit check, not a pressure setting for your site.

Does automatic compensation remove the need to check pressure?

Check what the meter actually does. Some DO meters have an internal barometer. Others ask you to enter the pressure or altitude. Older systems may need a pressure-adjusted saturation value. Follow the route in the manual.

The YSI DO handbook describes these approaches and emphasizes true local pressure. Confirm which approach applies before making an adjustment. Do not correct a reference value manually and then apply the same correction again in the controller.

An optical probe does not prove that the meter has a barometer. Ask the supplier to show you the pressure setting and how to use it. For the choice of probe type, see our optical versus membrane DO sensor comparison.

A pressure correction checklist for site calibration

Set up the probe as the manual specifies. Water-saturated air and air-saturated water are different methods. Use the right one and let the temperature settle. A new pressure setting cannot fix a torn membrane, dirty optical cap or poor setup.

CheckWhat to recordIf the check fails
Controller and sensorModel, sensor type and manual versionObtain the matching procedure
Calibration methodApproved air or water arrangementRebuild the setup before calibration
Pressure sourceLocal absolute value, unit and timeVerify the source and unit
Compensation routeBarometer, manual entry or altitudeResolve the setting before saving
Temperature and salinityValues and compensation settingsFollow the model's instructions
Result and verificationReading, acceptance criterion and operatorInvestigate before returning to control

Save the old settings before you make changes. After calibration, run the check in your site procedure. Record its result as well as the pass message. If the probe still drifts or responds slowly, use the DO sensor maintenance checks. Do not keep changing pressure to force agreement.

Why can two calibrated DO meters disagree?

Check the settings first. One meter may use today's local pressure. The other may still use a factory value or a setting from another site. Also compare the salinity input, temperature and percent saturation mode.

In a local oxygen saturation mode, the display can read 100% at different elevations. The mg/L value can still differ. Some meters use a standard pressure reference for percent saturation instead. Check the mode and unit before you judge the result.

Then compare the same water at the same time. Provide the flow each probe needs and avoid direct bubble contact. Water can change after you remove it from an aeration tank. If your quality procedure calls for an independent reference check, agreement between two meters is not enough.

What should you confirm before ordering an online DO system?

For continuous aeration monitoring, review the Tenber DOS-5301 dissolved oxygen controller or the DOS-5308 optical DO controller with the intended sensor. Confirm the pressure compensation method for the supplied configuration; do not assume either model has a built-in barometer.

For projects in Vietnam, Indonesia, Malaysia or the United States, give the actual site and elevation. A coastal plant and a high inland site may need different pressure inputs. The country name alone does not tell us the site conditions.

Send Tenber your DO application for a configuration review. Share the liquid, DO range, temperature, salinity, site pressure or elevation, mounting method and cable length. State the sensor type and PLC signals you need.

For an existing system, add the controller model and a photo of its calibration settings. These details help us check the controller and sensor pair before quotation.

Frequently asked questions

Should I use the pressure shown in a weather app?

Only after checking what it represents. Many weather values are corrected to sea level. A DO meter requesting true barometric pressure needs the local absolute value, in the specified unit.

Should tank depth be added to the calibration pressure?

Not when the procedure asks for local atmospheric pressure during an air calibration. Submerged or pressurized operation is a separate application condition. Confirm any required compensation with the sensor manufacturer.

Should I enter a fixed mg/L value at air saturation?

Only if the approved procedure calls for it, using the correct temperature, pressure and salinity reference. Air saturation does not correspond to one fixed mg/L value at every site.

Request a Quote